How to Program 2005 Honda Civic ECM by Autel MaxiIM IM608

2005 Honda Civic that has been replacing an refurbished engine computer(ECM). The immobilizer light is on because its module is not programmed to the car with VIN number or security system.  Here is the tutorials to use the Autel MaxiIM IM608 to solve it.

Let’s get this car cranked, with not start.

And connect to Autel IM608, click

Diagnostics >> Honda >> Accept >> Automatic selection >> Read >> OK >> USA >> Yes >> Diagnosis >> Control unit >> IMMOBI

Keep ignition ON until the tester directs you to turn the ignition off.

The tester cannot program keys with a T5 stamped on the blade of the key or with the word ILCO on the plastic head. These keys can only be programmed with the ILCO key duplicator.

It’s 3rd immobilizer.

Immobilizer setup >> Special function >> Replace ECM/ PCM

This function does necessary registration for ECM/PCM replacement.

When the ECM/PCM is replaced, it is necessary to be recognized a code each other to the ECM/PCM and the immobilizer Control Unit-Receiver with the diagnostic tool. Also, the vehicle with Keyless Access System needs to be recognized a code each other to the ECM/PCM and Keyless Access Control Unit. Otherwise, the engine cannot be started.

After replacing the ECM/PCM and registering the keys, the new ECM/PCM must be checked for the latest program.

The registration of immobilizer codes into the immobilizer unit has been completed.

Turn the ignition switch off.

Check all keys to ensure each will start the engine.

Turn the ignition switch on.

Is this vehicle equipped with a Keyless Access system? No

Before selecting yes, remove the immobilizer key from the vehicle remote, place into the ignition, then turn on.

At this point, immobilizer light is already out.

Let’s try to see if the car starts, it starts normally.

Done.

This is how to program an used engine computer for Honda replacement with Autel IM608.

Lonsdor K518ISE program Key for Nissan Qashqai 2015

 

There are two options for Nissan Qashqai blade key. Here is the guide to add a spare key to Nissan Qashqai 2016 with Lonsdor K518ISE Key Programmer.

Connect K518 host with vehicle via OBD diagnostic socket

Turn ignition on

Select Immobilizer->Nissan->Select from type->Immobilizer->New 20-digit rolling code->Add key

Turn ignition off and turn on emergency flasher

Insert the key to be programmed and turn ignition on

Turn ignition off and turn on emergency flasher

Open and close driver door for twice

Lonsdor K518 asking all keys will be detected

Communication processing

Switch on with a working key

Check if the dash indicators turn on and the security light goes off within 1 few seconds. If yes, press OK to continue

Switch ignition off

Program success, continue to program next key?

Switch ignition on with a key

Check if the dash indicators turn on and the security light goes off within 1 few seconds. If yes, press OK to continue

Turn ignition off

Program success, continue to program next key?

Turn ignition on with the first key

Program completed.

If you want to know more about Key Programmer, please click our website: https://www.obd2tool.com

Lonsdor K518ISE Program Ferrari 458 Keys

Lonsdor K518ISE(K518 English Version) universal auto key programmer , with wider vehicle coverage in key programming, it is customized as the first masterpiece to the overseas market from Lonsdor. With months of preparation and rigorous testing, from the software design to the user experience, it is an epitomize of Lonsdor years of industry experience. It is tailored and perfect for vehicle locksmith, to help making their work easier, faster and more powerful!

Lonsdor K518ISE Main Functions & Features:
1.Immobilization
2.Chip Generation/Copy
3.Remote Frequency
4.Odometer Adjustment
5. Free BMW FEM key programming
6.Program Toyota/Lexus smart key all key lost via OBD
7. Built-in Volkswagen 4th 5th adapter

Lonsdor K518ISE key programmer support Ferrari 458,F12,F149 key programming. Here is a case about Lonsdor K518 program Ferrari 458 remote key.

Device: Lonsdor K518ISE key programmer

Key type: Ferrari 458 remote

Test procedure:

Step 1: Backup immo data

Step 2: Program key

Step 3: Program remote

Test result: success!

Detail steps check the photos:

Choose Ferrari Brand

Choose The car model 458

Choose Immobilizer

Show the detail info and read the data

Backup the data

Lonsdor K518ISE Program

Then Program remote

Success

If you want to know more about Car Key Programmer, please click our website:https://www.obd2tool.com

What is a Key Programmer

 

A car key programmer is a device that can be used to recode the transponder in a mechanical key or fob. Some modern automobiles have specially coded transponders in their keys and will not start or drive unless the correct signal is received. In some cases, a new key can be programmed without any special equipment, although many vehicles require a device called a key programmer. A key programmer can be a standalone entity, although sometimes integrated with complex scanning tools. Key programmers typically connect bi-directionally to the On-Board Diagnostic II (OBD-II) port.

When a key is replaced on a modern automobile, the new unit often turns the mechanical switch but fails to initialize the system or start the vehicle. When this occurs it is usually because the transponder in the key has not been coded for that particular system. Keys can often be obtained from either a dealer or a locksmith, although they must be coded regardless of source. Some vehicles allow the owner to code their own key, which usually requires the presence of one of their original keys. This process differs from vehicle to vehicle, although it usually consists of inserting the original key into the ignition, depressing a special combination of brake and accelerator pedals, and then replacing the original key with the new, uncoded one.

When a vehicle does not have a self-programming feature, a key programmer is usually required to do the job. These programmers are typically bi-directional OBD-II tools that connect to the same location as other scan tools. Many vehicle manufacturers sell units that program keys specifically for their vehicles, although generic units that can handle a variety of makes and models can also be found.

The process of using a key programmer typically involves plugging the tool into the OBD-II interface so it can communicate with the vehicle. Each programming tool has different options and procedures, although they usually allow the operator to retrieve the programming data from the computer and then recode the transponder and computer to make them work together. After using the key programmer, the new key should work the same as the old one.

Some vehicles use key fobs instead of traditional lock and tumbler keys. In some cases, the key fob only needs to be in close proximity to the vehicle to work, while other cars require it to be inserted into the dashboard. Key programmers can be used with these fobs in many cases and the process is usually similar to regular keys.

Lonsdor K518ISE program Mazda CX9 Second generation 2017 all key lost

 

This instruction will show you guide on how to program all key lost for Mazda CX9 Second generation 2017 By Lonsdor K518ISE.  More cases about Mazda, please click to Ford Trouble Repair.

we got a Keyless system malfunction at the dash.

We have two genuine original keys that for this vehicle, they both do operate the vehicle at the moment, but to get rid of the malfunction, we have to perform an old keys loss scenario for this vehicle and reprogram both the original keys.

Procedures:

Turn the ignition to the on position, make sure all the lights on the dash up

Click “Immobilization” on the Lonsdor

Select “Mazda”, then select correct model for your vehicle

Select “Smart Key”

Select “All smart keys lost”

At least 2 smart keys are required, click “OK”

Following shows the information of the vehicle, continue with “OK”

Next if you can switch ignition on, click “OK”

Identified number of programmed keys in car: 4, we actually only 2, but it’s ok

Wait about 7 minutes, then the horn will ring.

If you do not hear the horn, click “Cancel” to return then follow the screen information operating.

After read “Keep the unregistered smart key at hand”, click “OK”, then turn ignition on, place the first one smart key, until you get a beep.

Identified number of programmed keys in car: 1, click “OK”

Then switch ignition off.

Lonsdor will tell you turn the ignition on again in a second key. Same operation for second key.

After do that, we need to do remote side of things.

Press on brake, then you can see a green flashing light. Press the start button to start the car with the smart key(logo side down) and let it run for three seconds, then switching ignition off. The first key done.

Release the brake then do same operation for second key.

If you want to know more about Key Programmer, please visit our website: https://www.obd2tool.com