How to Program 2005 Honda Civic ECM by Autel MaxiIM IM608

2005 Honda Civic that has been replacing an refurbished engine computer(ECM). The immobilizer light is on because its module is not programmed to the car with VIN number or security system.  Here is the tutorials to use the Autel MaxiIM IM608 to solve it.

Let’s get this car cranked, with not start.

And connect to Autel IM608, click

Diagnostics >> Honda >> Accept >> Automatic selection >> Read >> OK >> USA >> Yes >> Diagnosis >> Control unit >> IMMOBI

Keep ignition ON until the tester directs you to turn the ignition off.

The tester cannot program keys with a T5 stamped on the blade of the key or with the word ILCO on the plastic head. These keys can only be programmed with the ILCO key duplicator.

It’s 3rd immobilizer.

Immobilizer setup >> Special function >> Replace ECM/ PCM

This function does necessary registration for ECM/PCM replacement.

When the ECM/PCM is replaced, it is necessary to be recognized a code each other to the ECM/PCM and the immobilizer Control Unit-Receiver with the diagnostic tool. Also, the vehicle with Keyless Access System needs to be recognized a code each other to the ECM/PCM and Keyless Access Control Unit. Otherwise, the engine cannot be started.

After replacing the ECM/PCM and registering the keys, the new ECM/PCM must be checked for the latest program.

The registration of immobilizer codes into the immobilizer unit has been completed.

Turn the ignition switch off.

Check all keys to ensure each will start the engine.

Turn the ignition switch on.

Is this vehicle equipped with a Keyless Access system? No

Before selecting yes, remove the immobilizer key from the vehicle remote, place into the ignition, then turn on.

At this point, immobilizer light is already out.

Let’s try to see if the car starts, it starts normally.

Done.

This is how to program an used engine computer for Honda replacement with Autel IM608.

Autel IM608 Program Toyota Corolla 2021 Smart Key

Autel MaxiIM IM508 and IM608 Released Toyota 2019-2021 Proximity Smart Key Programming without PIN or NASTF. Here Cnautotool.com introduce 2 ways to add spare key to Corolla with 4A proximity.

Way 1: Remove Smart Box
Way 2: Don’t need to remove smart box

Way 1: Remove Smart Key
Model example: Toyota Corolla Altis 2021

Remove Smart Box from the vehicle and connect with Gbox following operation guide
Select Toyota-Manual selection- Other- Corolla- 2009 onwards- Smart Key- ZRE (2019-)

Select Control Unit- Kyeless Ssystem(CAN)- Backup IMMO Data
Backing up EEPROM data that can be used to add more smart key without password
Remove the smart box and then connect with G-Box follow operation guide

Press Yes to continue
Communicating with the smart box

Backing up EEPROM
File your name file and press Save

Re-plug smart box back to the vehicle
Select Add Smart Key
Add more Key Max 4 keys
Turn on ignition switch
Turn ignition off and turn hazard light on
Press Yes to continue
Confirm you have backuped eeprom file from this vehicle

Choose your backup EEPROM data file

Touching working key on push start button if will hear 1 beep

Touching new key on push start button if will hear 2 beeps

Keep touching new smart remote on ignition button until finish
Turn on ignition switch
Touching ignition b button with new smart key again
Sound 1 beeplearn key success
Test remote, all remote ok
Way 2: Without removing smart box+ OBD

Connect G-box2 directly with fuse box of the smart box following the operation guide
The connect g-box2 with IM508/IM608 programmer

Follow similar steps in Way 1 to
1). Backup eeprom
2). Add smart key
3). Learn key.

How to Autel IM608 to Program Porsche Cayenne 93C86 Key

How to program a new key for Porsche Cayenne Continental with Autel IM608? Year 2008 is 315MHz with panic button. Autel XP400 Pro says chip not connected.

Solution:
Obd or on the bench. 2 options here. Sometimes it’s easy via obd. If not, then in the bank. Gasoline is usually ok by OBD. Diesel on bench. Normally. You need with cs and pin. You just can’t proceed without a PIN and CS. Remove the kessy read the 93c86 and get PIN and 7 digits cs. Then program via obd. CS needs to precode the key and then program it with the PIN code.

Just did one today.
1. Remove chip and read using APA002.
2. Dealer key
3. Load EEprom data
4. Make dealer key
5. Learn key

How to Add Key on Renault Duster 2017 by Autel IM608

Renault Duster 2017 is created by Autel MaxiIM IM608 in 3 minutes. easy money. IM608 can present Duster 2013. Add keys & all lost keys is the same, you have to program old and new from the beginning.

Go to Add key (guided)
Network is required during the process.
Step 1: Read Dflash data and save

Step 2:Read PIN

Step 3: Key learning

Insert key into ignition switch

Program successful

Remove and insert next key to be programmed

Program 2nd key success

Key learning completed.

Autel IM508/608 Program A New PCM on Honda Acura Guide

This article is about to show you how to program a new PCM for most Hondas and Acuras using Autel MaxiIM IM508/IM608.

The support list: https://www.autel.com/vehicle-coverage/coverage2

Here we have a Acura MDX 2005 to handle by the Autel IM508 Key Programmer.

This is the 3rd generation immobilizer, which is used on many Hondas like Accord or Acuras like TLX.

The car won’t start because of the new ECU in.

We will reprogram it, so the key will work again.

Go to

IMMO>>Acura>>Automatic selection

Turn on the ignition so it will pull out the VIN.

Then go to

The 3rd mechanical key system>>Replace ECM/PCM

After about 5 minutes, we’ve registered the PCM.

Meanwhile, the immobilizer light disappears.

Turn off the ignition as required.

Follow instructions to check keys.

The car starts without any issues.

Done! Nice and simple!

That’s the guide of programming a new PCM module using Autel IM508/Autel IM608.

This guide is from MODS FOREVER Team.

Any questions, contact us.