How to Program A New Key for Honda JADE 2015 by Launch X431

This illustration show you guide on how to use Launch X431 device to do new key programming for Honda JADE 2015.More test report about Launch X431 please check:Launch X431 Test report

Related Device:

Launch X431 V Pro or Launch X431 PAD V

Notes

1.You must have an original key;

2.Before performing the operation, ensure that the vehicle battery voltage is not lower than 12V and the device has sufficient power;

3.During operation, strictly follow the device prompts to switch ignition ON/OFF within specified time;

4.After the key registration completed, check whether all the keys normally open and close the doors and start the engine normally.

Steps

Turn off the ignition switch (if the ignition switch has been turned on), prepare all the keys, and connect the diagnostic device, enter the corresponding IMMO module, and select HONDA Anti-theft diagnostic software

2.Select the menu “Anti-Theft Key Matching”, the software will automatically detect the Anti-theft type and display the corresponding function menu

3.As described in above function introduction. Select the function “Add 1key”Note: The steps for Rewrite Keys and All Keys Lost are similar to the steps of this function.

4.Perform interactive communication with Anti-theft system and follow the prompts to operate after normal communication. Turn the ignition switch off.

Note: This operation will be performed more than once during operating, please perform by strictly following the prompts.

5.Turn the ignition switch to ON with an original key

6.Turn the ignition switch off within 17 seconds.

Note: This operation will be performed more than once during operating, please perform by strictly following the prompts.

7.Turn the ignition switch to ON with a new key within 20 seconds.

8.Turn the ignition switch off within 17 seconds.

9.Turnthe ignition switch to ON within 20 seconds without changing the key

10.Turn the ignition switch off.

11.Turn the ignition switch on

12.Check whether the immobilizer indicator light goes off.If it is not off, the matching failed; If it is off, continue to check whether the key matching is successful

13.Click “Yes”and it will prompt again to turn the ignition switch off

14.Turn the ignition switch to ON with an original key

15.The registration of keys has been completed.Turn the ignition switch off

16.Check all keys to ensure that each key can start the engine

17.Turn the ignition switch ON. Add 1Key completed.

For more Honda repair case,please refer to:Honda Trouble Repair.

Nissan Teana 2015 Key Programming by Launch X431

This illustration show you guide on how to use Launch X431 device to do key programming for Nissan Teana 2015.

Related Device:
Launch X431 V Pro or Launch X431 PAD V

Notes:
1.Obtain all the keys, and ensure that the vehicle battery voltage is not less than 12V and the device has sufficient power. Do not use devices that emit strong electromagnetic waves around the antenna of Anti-theft locking system, such as mobile phones, wireless transceivers, etc. when performing “Initialization ECU”

2.It is recommended to turn on the hazard warning light switch to prevent the ECU communication from entering the sleep mode during the execution of the function;

3.After the key registration completed, it is necessary to perform operation check on all registered keys to ensure vehicle remote controls and key ignition are normal.

Procedures:

1.Prepare the key that needs to be matched, connect the diagnostic connector, and select “IMMO”

2.Select the menu “Anti-Theft Key Matching”, the software starts to automatically scan the system and search for the Anti-theft mode of the vehicle model, click “OK”to enter the corresponding menu path.

3.Select the menu “Register Key”, it prompts to delete all registered key IDs, and then prompts the operation of turning off the power and turning on the hazard warning lamp

4.After clicking “Next”, the software will determine whether the power is turned off, if the poweris not turned off

It will automatically skip to step 8 when the power is off

5.After clicking “Next”, click the ignition button and touch the button with the key emblem side. With smooth network connection, the software will automatically obtain the Anti-theft password and perform the operation of Steering Lock Release. After the execution completed,it will display the prompt of powering on

6.After clicking“OK”, if the power is not turned on

it will automatically skip to step 7if the power is ON).

7.After the power is turned on, all key IDs will be automatically deleted, and the read key registration information and enter the prompt of key registration operation

8.Click the “Add”button to enter the interface of key registration operation prompt

operate the ignition switch and intelligent key according to the prompt, and click “Next”to step 9

9.After the registration operation, it is necessary to perform Complete Registration Key and Confirmation of Operation

More test report about Launch X431 please check:Launch X431 Test report