How to Program 2005 Honda Civic ECM by Autel MaxiIM IM608

2005 Honda Civic that has been replacing an refurbished engine computer(ECM). The immobilizer light is on because its module is not programmed to the car with VIN number or security system.  Here is the tutorials to use the Autel MaxiIM IM608 to solve it.

Let’s get this car cranked, with not start.

And connect to Autel IM608, click

Diagnostics >> Honda >> Accept >> Automatic selection >> Read >> OK >> USA >> Yes >> Diagnosis >> Control unit >> IMMOBI

Keep ignition ON until the tester directs you to turn the ignition off.

The tester cannot program keys with a T5 stamped on the blade of the key or with the word ILCO on the plastic head. These keys can only be programmed with the ILCO key duplicator.

It’s 3rd immobilizer.

Immobilizer setup >> Special function >> Replace ECM/ PCM

This function does necessary registration for ECM/PCM replacement.

When the ECM/PCM is replaced, it is necessary to be recognized a code each other to the ECM/PCM and the immobilizer Control Unit-Receiver with the diagnostic tool. Also, the vehicle with Keyless Access System needs to be recognized a code each other to the ECM/PCM and Keyless Access Control Unit. Otherwise, the engine cannot be started.

After replacing the ECM/PCM and registering the keys, the new ECM/PCM must be checked for the latest program.

The registration of immobilizer codes into the immobilizer unit has been completed.

Turn the ignition switch off.

Check all keys to ensure each will start the engine.

Turn the ignition switch on.

Is this vehicle equipped with a Keyless Access system? No

Before selecting yes, remove the immobilizer key from the vehicle remote, place into the ignition, then turn on.

At this point, immobilizer light is already out.

Let’s try to see if the car starts, it starts normally.

Done.

This is how to program an used engine computer for Honda replacement with Autel IM608.

How to Autel IM608 to Program Porsche Cayenne 93C86 Key

How to program a new key for Porsche Cayenne Continental with Autel IM608? Year 2008 is 315MHz with panic button. Autel XP400 Pro says chip not connected.

Solution:
Obd or on the bench. 2 options here. Sometimes it’s easy via obd. If not, then in the bank. Gasoline is usually ok by OBD. Diesel on bench. Normally. You need with cs and pin. You just can’t proceed without a PIN and CS. Remove the kessy read the 93c86 and get PIN and 7 digits cs. Then program via obd. CS needs to precode the key and then program it with the PIN code.

Just did one today.
1. Remove chip and read using APA002.
2. Dealer key
3. Load EEprom data
4. Make dealer key
5. Learn key

How to Add Key on Renault Duster 2017 by Autel IM608

Renault Duster 2017 is created by Autel MaxiIM IM608 in 3 minutes. easy money. IM608 can present Duster 2013. Add keys & all lost keys is the same, you have to program old and new from the beginning.

Go to Add key (guided)
Network is required during the process.
Step 1: Read Dflash data and save

Step 2:Read PIN

Step 3: Key learning

Insert key into ignition switch

Program successful

Remove and insert next key to be programmed

Program 2nd key success

Key learning completed.

Program Mitsubishi Triton 2019 AKL by Autel IM508 + Xhorse Key Tool Max

Use Autel MaxiIM IM508/ MaxiIM IM608 + Xhorse VVDI Key Tool MAX can successfully program Mitsubishi Triton 2019 when all keys lost. Refer to the following steps to start key programming.

Generate Remote
Put the smart key into the VVDI Key Tool MAX coil, go access
Vehicle remote >>Mitsubishi>> Eclipse Cross KeylessGo ID47 >> Generate Remote

Wait for processing until 100%…
Burn success.

Key Learning
Connect Autel IM508 with OBD2, select
IMMO >> Accept >> Mitsubishi >> Manual selection >> Australia >> TRITON(KK#, KL#) >> 2016- >> Smart key >> Yes >> Immo status scan >> Immo learning >> All keys lost

Insert a key into the key card slot, take all other keys out of the vehicle.
(The slot is near the bottom of the steering wheel, or in the co-pilot storage compartment. If there is no card slot, please close the key to the start button).

Learning succeeded.
Press “Yes” to learn the next one. Otherwise, press “No”.

Learning completed.
Test the key, it can normally start the car.
Done!

Both Autel IM508 Price & VVDI Key Tool MAX Price are lower than usual. Come to pick out your Christmas gift.

Mercedes All Keys Lost Programmed by Autel IM608 Scanner

This article is to guide customers through the whole process of All Keys Lost for a Mercedes with Autel IM608 Scanner. We need to do some necessary preparation before this All Keys Lost for a Mercedes Programming Test.

What tools are needed:
G-box, XP400 Pro, cable to connect XP400 Pro with EIS component, JVCI, JVCI cable
Make sure the network connection is good and follow the instructions for key learning with all keys lost.

Select the model type of “Mercedes Benz”, tap “Smart selection”>>All Keys Lost (Fast)>>On Bench (G-box Fast)

Since we are working on bench, we don’t need to read VIN.
We can check EIS number on the EIS and select it on screen. In this case, it is 209.
So tap “W209/2006-”, it will come to a Note like this:

Connect the power adapter to the G-box, follow the below diagram to connect the wires to EIS component.

You still have to connect the JVCI and JVCI cable to the G-box.
Ready to begin now!
Follow the instructions on the screen and enter a blank key into the XP400 Pro.

It will begin communicating the key. Please wait…

If there is no password for the key, tap “NO”. Then you will have to enter “Password Calculation process”.

Please strictly follow this:

This Password Calculation process will take about 5 minutes.

Success!

Once the Password Calculation process is completed, the key learning process will just take a few more seconds.

It is now at generating key file>>Write BE key file

Follow this step until it is done.

All keys lost completed!

The G-box makes the All Keys Lost process much simpler when working with a Mercedes.

A big success in all keys lost programming with Autel IM608 professional scanner.

How to program 2020 Subaru Impreza by Autel IM608

 

Autel IM608 Success: 2020 Subaru Impreza push start ign all keys lost 16 min in and out with 2 new smart keys

Don’t you think is it is like a 2k job at the dealer and they rest