How to Program 2005 Honda Civic ECM by Autel MaxiIM IM608

2005 Honda Civic that has been replacing an refurbished engine computer(ECM). The immobilizer light is on because its module is not programmed to the car with VIN number or security system.  Here is the tutorials to use the Autel MaxiIM IM608 to solve it.

Let’s get this car cranked, with not start.

And connect to Autel IM608, click

Diagnostics >> Honda >> Accept >> Automatic selection >> Read >> OK >> USA >> Yes >> Diagnosis >> Control unit >> IMMOBI

Keep ignition ON until the tester directs you to turn the ignition off.

The tester cannot program keys with a T5 stamped on the blade of the key or with the word ILCO on the plastic head. These keys can only be programmed with the ILCO key duplicator.

It’s 3rd immobilizer.

Immobilizer setup >> Special function >> Replace ECM/ PCM

This function does necessary registration for ECM/PCM replacement.

When the ECM/PCM is replaced, it is necessary to be recognized a code each other to the ECM/PCM and the immobilizer Control Unit-Receiver with the diagnostic tool. Also, the vehicle with Keyless Access System needs to be recognized a code each other to the ECM/PCM and Keyless Access Control Unit. Otherwise, the engine cannot be started.

After replacing the ECM/PCM and registering the keys, the new ECM/PCM must be checked for the latest program.

The registration of immobilizer codes into the immobilizer unit has been completed.

Turn the ignition switch off.

Check all keys to ensure each will start the engine.

Turn the ignition switch on.

Is this vehicle equipped with a Keyless Access system? No

Before selecting yes, remove the immobilizer key from the vehicle remote, place into the ignition, then turn on.

At this point, immobilizer light is already out.

Let’s try to see if the car starts, it starts normally.

Done.

This is how to program an used engine computer for Honda replacement with Autel IM608.

How to Add Key on Renault Duster 2017 by Autel IM608

Renault Duster 2017 is created by Autel MaxiIM IM608 in 3 minutes. easy money. IM608 can present Duster 2013. Add keys & all lost keys is the same, you have to program old and new from the beginning.

Go to Add key (guided)
Network is required during the process.
Step 1: Read Dflash data and save

Step 2:Read PIN

Step 3: Key learning

Insert key into ignition switch

Program successful

Remove and insert next key to be programmed

Program 2nd key success

Key learning completed.

Mercedes All Keys Lost Programmed by Autel IM608 Scanner

This article is to guide customers through the whole process of All Keys Lost for a Mercedes with Autel IM608 Scanner. We need to do some necessary preparation before this All Keys Lost for a Mercedes Programming Test.

What tools are needed:
G-box, XP400 Pro, cable to connect XP400 Pro with EIS component, JVCI, JVCI cable
Make sure the network connection is good and follow the instructions for key learning with all keys lost.

Select the model type of “Mercedes Benz”, tap “Smart selection”>>All Keys Lost (Fast)>>On Bench (G-box Fast)

Since we are working on bench, we don’t need to read VIN.
We can check EIS number on the EIS and select it on screen. In this case, it is 209.
So tap “W209/2006-”, it will come to a Note like this:

Connect the power adapter to the G-box, follow the below diagram to connect the wires to EIS component.

You still have to connect the JVCI and JVCI cable to the G-box.
Ready to begin now!
Follow the instructions on the screen and enter a blank key into the XP400 Pro.

It will begin communicating the key. Please wait…

If there is no password for the key, tap “NO”. Then you will have to enter “Password Calculation process”.

Please strictly follow this:

This Password Calculation process will take about 5 minutes.

Success!

Once the Password Calculation process is completed, the key learning process will just take a few more seconds.

It is now at generating key file>>Write BE key file

Follow this step until it is done.

All keys lost completed!

The G-box makes the All Keys Lost process much simpler when working with a Mercedes.

A big success in all keys lost programming with Autel IM608 professional scanner.

How to program 2020 Subaru Impreza by Autel IM608

 

Autel IM608 Success: 2020 Subaru Impreza push start ign all keys lost 16 min in and out with 2 new smart keys

Don’t you think is it is like a 2k job at the dealer and they rest

How to Program Range Rover Vogue 08 PCF7941 Key with Autel IM608

 

Many people had the same problem programming a spare key on this car- Range Rover Vogue 2008 PCF7941. They cannot program the key to this car with Autel MaxiIM IM608, Xtool, Zed full etc. Tried the same key sport/discovery it still failed.

Range Rover Vogue 2008 Pcf7941

Here’re tips on programming spare keys to this car.

Vogue 08 does not have CEM nor KVM module. Vouge has Lear leads box. It looks exactly the same as a BMW EWS. Under middle speaker or dash.

Anything with Hu92 is either EWS or Lear Leeds. Anything Hu101 is CEM.

Pull Lear module out and do it on bench.

Read eeprom 8 leg. Go in XP400 or XP400 Pro Programmer under Land rover Chip read and write. It will show you the wiring diagram.

Just make sure your transponder chip and frequency same as the original key.
on bench its doesn’t matter if you got the original key or not. It will work.

If adding via obd you need a dealer key.

If you haven’t got a dealer key then program from the immobilizer (LEAR) module. If you have a working key then you can clone the id46 chip.
You can use either remote with pcf7941 which will add the remote automatically or you can use BMW remote with separate id46 chip and manually add the remote as you would an EWS system BMW remote.  Transpoder clone with vvdi mini key tool (or any devices can clone id 46, handy baby, keydiy kd-x2, CN900mini etc ) remote programming by manual.

This just applies to the Range Rover Vogue. Range Rover Sport, Discovery 3 are completely different systems but most of people can’t seem to tell the difference.

Vogue is a BMW keyblade and immo different to sport which is a ford blade and different immo to vogue, one was built by bmw when owned other was when ford owned landrover

The Sport/Disco3 key is not compatible.

Original key should be pcf7936 but you can precode the pcf7941 into dealer key as said. Just pull the Lear box and crack on with it.

FYI: Easy with working key adapt to car with SKP900 or smart pro, londsor remote go in at same time.

Program Smart Fortwo 451 08-15 All keys Lost by Autel IM608

 We programmed a new remote key to a 2008 Smart Fortwo 451 with Autel MaxiIM IM608/IM508 because it lost all the keys. Car has the anti-theft indicator on.

   

Place the ignition switch. If we try to crank it, we got the message that it not programmed. This key is virgin.



Procedure:

2008-2015 Smart Fortwo (all keys lost, add key, EVU replacement) with Autel IM608

We go to Diagnostic instead of going to Immobilizer function.

Check vehicle information, has vehicle model and vin number here



We go to Control unit ->N10/10(SAM control)-> Control unit adaptations->Program key transponder codes





Insert key to be programmed into ignition and turn on ignition
Press F2 to start learning process



Turn off the ignition and then back on.



Press key ESC to interrupt rage teach-in process


The key has been successfully learned.
Press Yes
Learning key in progress
Press F4 STOP
Remove the taught-in vehicle key

Insert vehicle keys to be taught in into ignition lock and turn to position ignition on
The ignition must be switched on again within 20s



Key has programmed. Now you can start the engine with the new key.